How to Replace a Kia Sportage Replacement Key

For a number of Kia models, the key contains a built-in keyless entry system. This key is similar to the remote control and can be exchanged with a kia key fob replacement cost dealer.

Key fobs can stop working due to a variety of reasons, including batteries that are dead, worn-out buttons signal interference, or water damage. Here are some helpful tips on how to get your Kia Sportage replacement key back to working.

How to replace the remote key or smartkey

The battery in your 2013 kia soul key fob replacement's intelligent key will eventually need to be replaced, whether it's a remote or a push-to-start one, or a regular metal key that doesn't have a transponder. This is particularly relevant if your vehicle displays a message telling you that the smart or remote keys aren't powered.

This is a relatively simple process. To replace the battery in the keyfob remove your mechanical key from the slit that is located at the back of the fob. Then, you need to pry the cover off. Inside the key fob there will be tiny screws that hold the battery in its place. Using a small screwdriver, take the screw off and pull out the battery that was in place. Then insert the new one and close the hole in the key fob.

Test the key fob by pressing the lock/unlock buttons. If the doors lock and unlock in the same way, you're in good shape! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or you need to complete errands in Brandon.

Not all key fobs could need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If your key has to be reprogrammed, then you must be aware of the key code stamped on the key code tag and then record the number in a secure place.

How do I replace the battery?

If your kia picanto replacement key (linked internet site) key fob isn't responding when you press the lock or unlock button on the fob, this is a clear indication that the battery should be replaced. A low battery may also cause other problems like the check engine light turning on or delayed cranking of the engine. Fortunately replacing the battery on the key fob is a simple DIY project that requires only a few tools.

Before you begin the process before beginning the process, ensure that your vehicle is off and all doors are closed. Locate the small plastic piece on the bottom of your key fob and jiggle it until a metal key is released. The key can be put into the driver door handle to unlock your car.

To replace the key fob's battery, remove the cover from the back and use a plastic bar tool to loosen the latch holding the black negative battery cable. Remove the old battery, and then align the new battery so that the "+" positive side faces you, while the "-" negative side is facing towards the fob's electronic contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid bending or damaging the metal contacts.

Once the new battery is installed and the key fob is turned on, turn it off and on in the ignition until the door locks. You can then test your Kia's key fob to ensure it's working properly.

How do you replace the smart key?

You can have a standard keyfob or a Smart Key based upon the model of kia picanto smart key Sportage. The smart key is equipped with an embedded mechanical key blade, while the standard key fob does not. Both key fobs contain a battery that will eventually require replacing. It's an easy process that will take about two minutes.

Before you get started it is important to make sure that you are on a flat surface with good lighting and that your Kia is off. Also, keep in mind that there are tiny pieces inside the fob which could fall out if you are not vigilant.

The small release button is located on the lower backside. This will either be a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob open and you are able to take off the old battery and replace it. The new battery is one called CR-2032 and can be purchased from a local or online auto parts store. Once you're done you should be able to lock and unlock your car with your key fob, even if your engine isn't running!

How do you replace the mechanical key

The Kia keyfob can be a fantastic convenience, allowing us to lock or unlock our car by pressing one button. As with all devices like a key fob, the Kia may have issues. Luckily, there are ways to fix these issues and keep our key fobs in good working condition in the long run.

A dead or low-quality battery is among the most frequent problems. This can cause the device to stop working entirely or work intermittently. If this happens try replacing the battery with a fresh new one.

If this isn't enough to resolve the problem then try using a normal flathead screwdriver to open the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a brand new one.

After the new battery has been put in, close and open the doors with the mechanical key (every kia fob has an emergency mechanical key that will fit in the slot). Test the key fob to verify that it's working properly. Contact a dealer or a locksmith to solve the issue in the event that the fob is not working. Make sure they make you an emergency key that can work for all door and trunk cylinders to avoid lockouts in the future.